Please ensure Javascript is enabled for purposes of website accessibility

Fixture Repair

Fixture Repair | How to Go About It

Homeownership comes with additional responsibilities such as landscaping, snow removal, and performing regular repairs to ensure your house is in top condition. Such maintenance practices are also aimed at preventing further damage resulting in high repair costs. One of the areas that need repairs but are often ignored as it may seem minor are fixtures.

Whereas the sound of droplets falling into your sink can be deafening, especially in the dead silence of the night, they are rarely taken with the urgency they deserve. One droplet surely can’t do much harm? Well, data suggests otherwise.

One in every ten houses in the US wastes 90 or more gallons of water each day due to leaks. In total, leaks account for the wastage of 1 trillion gallons in the US each year. Water that is sufficient to cater to the needs of 11 million homes for one year. There is a great need to use resources such as water sustainably. Also, considering the extra costs you will incur, you should perform kitchen faucet repair anytime you notice a leak.

Read on to learn how to perform bathroom faucet replacement and why you are better off hiring a bathroom faucet replacement service in Myerstown.

Faucet Replacement

Before you begin your kitchen faucet replacement mission, make sure that you have all the necessary tools. These are:

With all the tools at hand, take the following steps to ensure kitchen faucet repair goes smoothly.

1. Shuft Off the Faucet's Water Supply

Not unless you want water spilling on you and all over the place, begin by shutting off the faucet’s water supply. Check under the sink for valves that you can use to stop the water supply. They’re usually located where supply tubes connect with the faucet’s tailpieces or at the stub-out pipes. In a clockwise direction, turn the valve to its limit.

Before you begin removing anything, turn the faucets to allow the water in its supply pipes to flow out.

2. Detach the Handle

The next step in bathroom faucet repair is removing the handle. On top of the faucet, you will see a cap covering the crew holding the handle and body of the faucet together. Remove the cap using a flat screwdriver by prying it upwards.

Take the hex wrench or Phillips screwdriver and use it to turn and remove the screw. With the screw out of the way, the handle will come right off. However, with old faucets, you may have to hit it lightly with a hammer to get it off. This is due to the mineral buildup, which causes the handle to get stuck. In case the hammer is ineffective, you will need a handle puller tool to remove it.

3. Remove the Faucet Valve Insert

Once the handle is off, proceed to remove the collar or retaining nut using a wrench. For Moen type of faucets, there’s likely going to be a pin inside. If so, pull it off using the pliers. After removing the nut, collar, or pin, lift the faucet valve insert. This is either a ball insert, ceramic disk, or cartridge. With ball-style valves, you only need your hand to unscrew the collar. When doing so, be careful as the spring-loaded valve housing can pop out and fall in the drainage.

4. Replace the Rubber Parts

Depending on the type of valve, there are many parts that you can find in the faucet. If your faucet uses a ball-valve or cartridge, you’re likely to find some rubber components within the inlet holes. Use a screwdriver to remove them and then replace them with a matching model. For cartridge faucets, you will also need to replace the O-rings.

5. Inspect the Components

Repairing a bathroom faucet should not be a regular activity. As such, when you have it open, inspect all the elements and replace those that seem damaged or nearly there. Best practice usually involves replacing all the washers and ball for ball-type valves. Another key area to inspect is the cartridge. Check for nicks and cracks.

6. Reassemble and Test the Faucet

After replacing all the damaged components, there’s only one thing left; checking whether your bathroom faucet repair is successful. To reassemble it, begin by reinstalling the valve and then tightening the retaining pin, retaining nut, or collar. Put the handle in place, tighten the screw, and put the cap back to cover the screw.

With everything in place, open the valves that let water through to the faucet and turn on your faucet. Water should flow out, and your leak should be gone.

Kitchen Faucet Service

It’s possible to take a DIY kitchen faucet replacement. However, if you do not have prior plumbing experience, you’re better off hiring a faucet repair professional service.
Countryside offers kitchen faucet replacement in Myerstown, Lancaster, Lebanon, Cornwall, and Reading. Contact us today for fast and reliable bathroom faucet replacement.